Alumawood Patio Cover in Pompano Beach: What You Get

Alumawood is a brand of embossed, powder-coated extruded aluminum built to look like painted wood — no rot, no termites, and no repainting. That's it. That's the product. Everything else you'll read about it is either a benefit of aluminum or a limitation of aluminum, and this page covers both honestly.

The name causes half the confusion in this category. People assume there's wood somewhere in it, or that it's a composite. There isn't and it isn't. It's aluminum wearing a very convincing costume, and the costume holds up from about six feet away, which is where you'll be standing.

What you're actually buying

An Alumawood-style cover is a set of hollow aluminum extrusions — posts, beams, rafters and fascia — with a factory-baked powder coat over an embossed grain texture. The roof deck on top is where the real decisions live:

• Lattice: open blades, roughly 40 to 70 percent shade depending on spacing and blade width, and rain goes straight through.
• W-pan solid: an inverted-W panel profile that stiffens the deck and drains water inside the pan rather than off a flat surface. That geometry is why a W-pan commonly spans 8 to 14 feet with no intermediate support.
• Flat-pan solid: cleaner-looking from underneath, less inherently stiff, so it usually needs more beams across the same distance.
• Insulated foam-core: an EPS or polystyrene core between two aluminum skins in 3, 4 or 6 inch thicknesses, landing roughly around R-11 to R-24.

Skins are commonly 0.024 to 0.032 inch on residential jobs. That number is worth asking about, because it's the single easiest place for a cut-rate quote to save money without you noticing until something dents.

The honest good list

No rot. Water is the thing that kills wood covers, and it does it from the inside where you can't see it. Aluminum doesn't care.

No termites. Nothing in the structure is food.

No repaint cycle. A powder coat is cured onto the metal in a factory oven, not brushed onto your beams in August. A cedar cover, by contrast, wants cleaning and resealing about every two to three years, forever. Over ten years that's the real cost difference, and it's bigger than the difference in the quotes.

Cool to the touch, relatively. Compared with bare mill-finish aluminum, a light powder-coated finish reflects better and the hollow extrusions hold less heat. It's not cold. It's just not the frying pan people expect from metal.

The honest bad list

Any contractor who tells you the downsides don't exist is selling, so here they are.

It dents. Aluminum extrusion is strong along a span and soft against a point impact. Drop a ladder on a rafter and you'll have a permanent reminder of that afternoon. The good news is that fascia and individual panels are usually replaceable pieces rather than a whole-cover problem.

The color palette is limited. You're picking from a manufacturer's finish list — typically a handful of whites, sandstones, browns and a dark bronze. If you have a specific paint chip in mind, aluminum will not match it, and field-painting a powder coat is a project you'll regret.

Up close, it's metal. The embossed grain is good. It is not cedar. If you and your guests will be sitting three feet from a post all summer noticing that, buy the wood and accept the maintenance calendar. That's a legitimate choice and we'd rather you make it on purpose.

What actually determines whether it holds up

Here's the part that has nothing to do with the brand on the extrusion and everything to do with whether your cover is still there in fifteen years.

Footings. A typical residential post footing runs 12 to 24 inches in diameter and 18 to 36 inches deep, with frost depth setting the number in cold markets. Simpson-style post bases hold the post off the concrete so the base isn't sitting in standing water for two decades.

Ledger and flashing. An attached cover hangs off a ledger lagged into your house band joist. A badly flashed ledger is the number-one way a patio cover causes a rot problem — and the irony of a rot-proof aluminum cover rotting out your house framing is not lost on anyone in this trade. If the roofline or stucco won't take a clean ledger, go free-standing with two extra posts.

Wind engineering. Covers get designed to a wind speed under ASCE 7 as adopted by your local IRC or IBC code, commonly somewhere in the 90 to 140 mph range and much higher in coastal high-velocity hurricane zones. In those coastal markets an inspector will want Miami-Dade NOA or state product approval numbers on the components themselves. In snow markets, snow load drives the beam sizing instead. Check your jurisdiction's actual numbers rather than trusting a national figure from a brochure.

The mistake we get called about

The call comes in as "my patio cover is failing." Nine times out of ten, someone walks out, looks up, and finds a fascia section that's worked loose or a post base with a couple of backed-out lag bolts. That's a $40 hardware fix and twenty minutes with a socket wrench, not a replacement. Tighten it, replace the fastener with the right stainless one, done. If a company looks at a wobbly post base and quotes you a new cover, get a second opinion before you get a new roof.

Genuine replacement territory is different: crushed or buckled beams, a ledger with water damage behind it, or footings that have heaved. Everything else is usually patio cover repair work measured in hours.

The one strong opinion here

Buy aluminum for the structure, and spend your upgrade money on the roof deck instead of the finish. The difference between a basic powder coat and a premium one is a few hundred dollars and a slightly nicer sheen. The difference between a plain pan and an insulated foam-core panel is roughly $10 to $20 a square foot and it changes whether you can sit out there at 3 p.m. in July. One of those you notice every single day. The other you notice during the sales meeting.

If you're weighing open blades against a full deck, our guide to lattice vs solid patio covers walks through the shade and rain tradeoff in detail, and the patio cover cost breakdown has the full pricing ladder.

Bottom line

Alumawood-style covers are the low-drama pick: aluminum strength, a wood-ish look, and a maintenance schedule that consists of pointing a hose at it occasionally. Accept that it dents and that you're choosing from a set palette, put the savings into a better roof deck, and make sure whoever installs it flashes the ledger properly.

Pompano Beach Elite Patio Covers installs powder-coated aluminum and insulated patio covers across Pompano Beach and north Broward County, along with aluminum pergolas when open rafters suit the space better. We'll tell you the panel gauge, the span, and the honest downsides before you sign anything. Call (844) 511-2320.